The system uses a PWM dimmer and is designed for use in entire cockpits equipped with incandescent bulbs. Of course, LEDs can also be dimmed using the system. The basic components are the base module and the driver module. The base module commands the brightness, while the driver modules are used to control the lamps. Multiple driver modules can be connected to a single base module to allow for the simultaneous dimming of different types of lamps (voltage and sink/source type) or to dim higher currents.

The base module and the drivers are connected to each other using a 6-pin ribbon cable (1.27/2.54 mm pitch). This cable carries the dimming signal and is used to control the drivers.

In the source type configuration, the negative terminal of the lamps is permanently connected to ground. The transistor on the circuit board is connected to the positive power supply and switches the power to the positive terminal of the lamps to complete the circuit.
The type you need depends on the application. If the lamps are completely isolated, the type doesn’t matter. However, if, for example, one side of your lamps is connected to the aircraft structure (ground), you’ll need the source type, which specifically supports this fixed connection of the negative side to ground.

Voltage max. 30 V, load max. 5 A.
A base module is required for dimming.

Der Beitrag Dimmer v3 Driver Source erschien zuerst auf Cockpit Concept.

The board also has a generator for a 400 Hz alternating voltage, which can be varied between 0 and 5 V (RMS) via the software. The lighting of most devices can be operated with 5 V DC without any problems. However, some devices require an AC control voltage to operate and vary the lighting. These are the APE-5100 clock, the DCDU and the full-format printer (Widebody). Similar to other boards, the data source can be selected and a value table can be created for calibration. A total of three connections are available for the voltage (AC signal and ground).

Please note that the output power is only designed as a control voltage for the above-mentioned devices. The circuit board cannot be used to control incandescent lamps.

An external 5 volt power supply is required.

Der Beitrag HS TX AC Backlight, LAN erschien zuerst auf Cockpit Concept.

The system uses a PWM dimmer and is designed for use in entire cockpits equipped with incandescent bulbs. Of course, LEDs can also be dimmed using the system. The basic components are the base module and the driver module. The base module commands the brightness, while the driver modules are used to control the lamps. Multiple driver modules can be connected to a single base module to allow for the simultaneous dimming of different types of lamps (voltage and sink/source type) or to dim higher currents.

The base module and the drivers are connected to each other using a 6-pin ribbon cable (1.27/2.54 mm pitch). This cable carries the dimming signal and is used to control the drivers.

In the sink type configuration, the positive terminal of the lamps is permanently connected to the positive terminal of the power supply. The transistor on the board acts as a switch that connects the negative terminal of the lamps to ground and completes the circuit.
The type you need depends on the application. If the lamps are completely isolated, the type doesn’t matter. However, if, for example, one side of your lamps is connected to the aircraft structure (ground), you’ll need the source type, which specifically supports this fixed connection of the negative side to ground.

Voltage max. 30 V, load max. 5 A.
A base module is required for dimming.

Der Beitrag Dimmer v3 Driver Sink erschien zuerst auf Cockpit Concept.

The system uses a PWM dimmer and is designed for use in entire cockpits equipped with incandescent bulbs. Of course, LEDs can also be dimmed using the system. The basic components are the base module and the driver module. The base module commands the brightness, while the driver modules are used to control the lamps. Multiple driver modules can be connected to a single base module to allow for the simultaneous dimming of different types of lamps (voltage and sink/source type) or to dim higher currents.

The brightness can be adjusted using a potentiometer (100 ohms to 1 megohm), which is not included.
The board has an input that can be used to turn off the dimmer. In this case, the connected lamps are turned off. To do this, ground must be applied to the input.
The dimmer requires its own stable 5 V power supply, which must not be subjected to a high PWM load.

Potentiometer not included in the delivery contents.

An external 5 volt power supply is required.

At least one driver module is required for dimming.

Der Beitrag Dimmer v3 Base Standalone erschien zuerst auf Cockpit Concept.